Deep inside a nuclear power plant or a sprawling warehouse, the humble power cable is both lifeline and liability. Wrapped in PVC sheathing and XLPE insulation, these cables carry electricity through some of the most safety-critical environments on Earth, yet their plastic armor is combustible. When fire strikes, cables can stop carrying power and start spreading flames, disabling the very firefighting and safety systems designed to protect the facility. A new study from researchers at IIT Roorkee, GD Goenka University, UPES, Johns Hopkins University, and the Bhabha Atomic Research Center has now quantified, layer by layer and second by second, exactly how long a live power cable survives under radiative fire exposure, and how much protection a thin fire-retardant coating can buy.The team, led by Raj Kumar Mishra of IIT Roorkee's Fire Research Laboratory and Mahesh Kumar Tiwari of GD Goenka University, published their findings in Frontiers in Thermal Engineering on 13 August 2025. Their motivation is rooted in hard lessons from industrial history. During the initial stage of the 2010 fire at Dalian's oil depot in China, flames damaged electricity supply cables and distribution rooms, interrupting the low-voltage power supply needed to electrically shut off emergency tank valves. Manual valve operation was slow and dangerous, and firefighting efforts suffered enormously. The episode illustrated a chilling truth: in a fire, key cables connected to safety equipment become the weak point of the entire emergency system.To probe this vulnerability under controlled conditions, the researchers designed a bench-scale experimental campaign around a 1.1-kV, four-core, XLPE-insulated, armored, PVC-sheathed power cable with an aluminum conductor. The cable had an outer diameter of 26.2 millimeters and a current rating of 70 amperes. Specimens were cut to 1.2 meters in length, with 100 millimeters stripped from each end, leaving an experimental length of 1,000 millimeters. Two precisely drilled holes reached the insulation and the aluminum core, where high-accuracy K-type thermocouples were inserted to track temperatures deep inside the cable. Additional thermocouples monitored the outer surface and the flame itself, while a step-up transformer and variac supplied rated current through copper bus bars throughout the test.The experimental protocol unfolded in three phases. First came the current phase, in which the cable carried its rated load for 20 to 25 minutes until its temperature reached a steady state, mimicking normal operation. Then the pre-burning phase began: fuel from a reservoir pan, maintained at a constant 50-millimeter fuel level, ignited and bathed the cable in external radiation. Finally, the burning phase arrived, when the cable itself became a source of ignition. The team defined failure by two criteria: electrical failure, marked by a short circuit when insulation damage caused a breakdown, and mechanical failure, when the cable surface began smoldering, igniting, or flaming. Both failure modes were considered in every test.Experiments were conducted at two average heat flux levels, roughly 15 kilowatts per square meter (13 to 15 kW/m2) and 20 kilowatts per square meter (17 to 20 kW/m2), achieved by adjusting the distance between the burner and the cable. For each heat flux, five fire-retardant coating thicknesses were tested, ranging from 0 to 0.8 millimeters, yielding ten experiments in total. The fire-retardant paint, or FRP, was prepared by mixing 10 grams of flame-retardant agent with 10 milliliters of fire-retardant paint, with epoxy thinner added to improve workability. A single coat achieves 90 to 100 microns of thickness and dries within 20 to 24 hours. The cured coating was characterized on a physical property measurement system, revealing an average thermal conductivity of 1.633 watts per meter-kelvin, a specific heat capacity of 1,690.581 joules per kilogram-kelvin, and a density of 1,272.308 kilograms per cubic meter. Coating thickness was verified with a CALTECH gauge accurate to 1.5 percent or 2 percent.The results for uncoated cables are sobering. Under an average heat flux of 15 kilowatts per square meter, the bare cable failed after 1,897 seconds, with the aluminum core reaching 282.60 degrees Celsius and the outer sheath 353.90 degrees Celsius at the moment of failure. Raising the heat flux to 20 kilowatts per square meter nearly halved the survival time: the cable failed after just 991 seconds, with core and sheath temperatures of 223.16 and 310.16 degrees Celsius respectively. The counterintuitive drop in failure temperature at higher heat flux reflects the thermal impact of intense radiation, which degrades the insulation faster than heat can diffuse inward, so the sheath breaks down before the core heats fully.Coatings changed the picture dramatically. At 15 kilowatts per square meter, failure time increased from 1,897 seconds for the bare cable to 2,017 seconds at 0.2 millimeters of coating, 2,140 seconds at 0.4 millimeters, 2,241 seconds at 0.6 millimeters, and 2,542 seconds at 0.8 millimeters, a gain of nearly 11 minutes. At 20 kilowatts per square meter, failure times rose from 991 seconds bare to 1,204, 1,300, 1,386, and 1,522 seconds across the same thicknesses. The ignition time increased almost linearly with coating thickness, and the coating also altered failure chemistry: instead of melting and dripping off, the treated insulation hardened, adhering to the cable as solid particles or falling off in layers, making the burning cable less hazardous than bare wire. The fire-retardant paint suppresses the intense heat flux directly striking the cable and restricts flame spread along its surface.Using the measured data, the team developed empirical correlations for cable failure time as a function of heat flux and coating thickness, fitted by least-squares regression. The correlations agreed with experimental results within 2 percent variation and provided a conservative estimate of time to failure. The researchers also introduced a temperature reduction ratio, or TRR, defined as the difference between the steady-state surface temperature of uncoated and coated cables divided by the bare cable temperature at failure. For the 15 kilowatts per square meter case, the maximum experimental TRR of 0.1822 occurred at 0.8 millimeters of coating, suggesting a critical thickness of 0.8 to 1.0 millimeters. For the 20 kilowatts per square meter case, the maximum experimental TRR of 0.1813 appeared at 0.2 to 0.4 millimeters, indicating that the optimal coating thickness depends on the fire's thermal stress.To extend the bench-scale findings, the team built a three-dimensional numerical model in COMSOL Multiphysics, replicating the cable's complex cylindrical geometry with four aluminum cores, concentric insulation, inner sheath, galvanized steel armor, and outer PVC jacket. The mesh consisted of approximately 1,063,432 extremely fine tetrahedral el
Source: BIOENGINEER
